1-855-976-5190

Request a Quote
AM-Series 4500 Ambient Air Cleaner
AM-Series 4500 Ambient Air Cleaner - Image 2
AM-Series 4500 Ambient Air Cleaner - Image 3
AM-Series 4500 Ambient Air Cleaner - Image 4
Ambient Air Cleaners

AM-Series 4500 Ambient Air Cleaner

Guarantee a cleaner air facility with Diversitech’s Filterhawk AM-Series 4500 Ambient Air Cleaners. Using a circular airflow pattern, the AM-Series 4500 draws dust, smoke and other airborne pollutants in through the sides and exhausts clean air out, protecting workers from harmful contaminants. Equipped with MERV 7 prefilters, a MERV 8 panel filter and MERV 14 primary multi-pocket bag filters, the AM-Series 4500 has a two-stage filtration system to effectively collect airborne toxins.

These ambient air cleaners are constructed using powder coated steel. The modular configuration of the Filterhawk allows units to be combined with multiple modules in a double or quad setup to increase the amount filter media. The air cleaners can be easily installed in your facility with an optional wall mounting bracket or eyebolts to hang the units with chains. Ideal applications for the AM-Series-3000 include: welding smoke and fumes, wood dust, oil mist and smoke from machining and dust from grinding.

Recommended Applications

  • Ideal for welding.
  • Ideal for grinding.
  • Ideal for deburring.
  • Ideal for oil Mist.
  • ideal for sanding
  • Not ideal for painting
Request a Quote

Overview

Guarantee a cleaner air facility with Diversitech’s Filterhawk AM-Series 4500 Ambient Air Cleaners. Using a circular airflow pattern, the AM-Series 4500 draws dust, smoke and other airborne pollutants in through the sides and exhausts clean air out, protecting workers from harmful contaminants. Equipped with MERV 7 prefilters, a MERV 8 panel filter and MERV 14 primary multi-pocket bag filters, the AM-Series 4500 has a two-stage filtration system to effectively collect airborne toxins.

These ambient air cleaners are constructed using powder coated steel. The modular configuration of the Filterhawk allows units to be combined with multiple modules in a double or quad setup to increase the amount filter media. The air cleaners can be easily installed in your facility with an optional wall mounting bracket or eyebolts to hang the units with chains. Ideal applications for the AM-Series-3000 include: welding smoke and fumes, wood dust, oil mist and smoke from machining and dust from grinding.

Benefits

  • Cost effective, energy efficient units
  • Modular design, multiple configurations
  • Quick install, no ductwork required

Features

  • 4500 CFM, 3 HP TEFC Motor
  • Powder-coated Steel Interior Frame
  • Lightweight Black Matte Recycled Polyethylene Plastic Panels
  • Chain-hung or Wall-mounted

Options

  • Wall-mounting Bracket
  • Baffle Impingers
  • Magnahelic Gauge
  • Manometer
  • Carbon Odor Absorption Kits
  • Factory-installed Eyebolts
  • HEPA Filter
  • Spark Baffles

Models and Options

Technical Specifications

Model (Product Number) Motor (H.P.) Air Flow (CFM) Volts/Phase/Hz Amps Net Weight1 Width1 Height1 Length1 Filter Quantity Pre-filter Type Filter Type
FH-A-4500 3.0 4500 230/460/575V/3/60Hz 9.6/4.8/3.9 194.14 25″ 25″ 72″ 6 MERV 7 (2x) MERV 8 Paper Pleated (2x) / MERV 14 Bag Air Filter (2x)

1 – Product weight and dimensions are based on base-models and may vary depending on selected product features. Please contact us for an accurate shipping quote.

Learn how to get the most out of your AM-Series 4500 Ambient Air Cleaner.
See our help topics and download the AM-Series 4500 Ambient Air Cleaner product guide and owner’s manual.

How to..

+ Set up your AM-Series 4500 Ambient Air Cleaner for the first time

 

Before You Begin

The system’s weight must be taken into account when choosing the proper installation method. Follow all applicable building and electrical codes. Mounting materials must be able to support the weight of the air cleaner plus weight of the material collected. Consult local building code for proper installation methods and materials.

Installation

There are three main ways of installing your AM-Series Ambient Air Cleaner:

  • Chain Hanging (eye bolts factory installed as option)
  • Rod & Cradle
  • Angle Braces
+ Perform Routine Maintenance

 

For optimal performance, routine maintenance is highly recommended. Do the following:

  1. Vacuum dirt accumulations in and around vent openings. (Dirt accumulations can cause motor overheating and a fire hazard.)
  2. Clean enclosed motors with an air jet (wear eye protection).
  3. Periodically inspect the installation. Check for:
    • dirt accumulation
    • unusual noises or vibration
    • overheating
    • worn or loose couplings, sheaves and belts
    • high motor current
    • poor wiring or overheated connections
    • loose mounting bolts or guards
    • worn motor starter contacts.
  4. Dayton ball-bearing motors without lubrication provision do not require periodic relubrication. Where motor has provision for bearing lubrication, lubricate as follows:
    1. After stopping motor and disconnecting power, thoroughly wipe the housing around both of the motor bearings, filler and drain plugs (on TEFC) ratings, remove fan cover for access to plugs).
    2. Remove filler and drain plugs and install a 1/8” pipe thread lube fitting in filler hole.
    3. Using a low pressure grease gun, pump new grease into motor until it appears at the drain hole.
    4. Run motor for several minutes to discharge excess grease. Shut motor OFF, replace filler and drain plugs, and reinstall fan cover.

Troubleshooting

+ My Unit's Motor Doesn't Turn On

 

When the motor on your AM-Series Ambient Air Cleaner doesn’t turn on, try the following:

  1. You may have a blown fuse.
    • Replace with time-delay fuses.
    • Check for grounded winding.
  2. The voltage may be too low at motor terminals due to line drop. Consult local power company.
    • Increase wire gauge.
    • Check for poor connections.
  3. The overload in motor start may have been tripped.
    • Check and reset overload relay in starter.
    • Check heater rating against motor nameplate current rating.
  4. Overload (internal thermal protector) may have been tripped.
    • Check motor load.
    • If motor has an automatic or manual reset thermal protector, check if tripped.
  5. Improper line connections.
    • Check connections against diagram supplied with motor.
  6. Check to see if the motor is overloaded.
    • Reduce load or increase motor size.
  7. Check the motor or starter to see if defective.
    • Repair or replace motor.
+ My Motor Stalls During Operation
  1. Check if the motor is overloaded. If so, reduce load. Otherwise, you may need to upgrade your motor size.
  2. Check the motor voltage as it may be too low. Verify that nameplate voltage is maintained.
+ My Motor Vibrates or is Excessively Loud

When your AM-Series unit’s motor vibrates or is excessively noisy, check the following:

  • Check the motor shaft to see if it’s misaligned. Realign if needed.
  • The 3-phase motor may be running on single phase.
    • Check for open circuit, blown fuses or unbalanced voltages.
  • Voltage may be high or unbalanced.
    • Check wiring connections. Consult local power company.
  • The bearings may be worn, damaged, dirty or overloaded.
    • Replace bearings.
    • Check loading and alignment.
  • Check winding to see if it’s defective. Check the shaft to see if it’s bent or bowed. Repair or replace.
  • Check for a loose sheave or misaligned coupling. Tighten set screw(s); realign coupling.
+ Airflow is Insufficient

 

If you find the airflow being generated by your AM-Series unit is insufficient, check for the following possible causes:

  • The blower speed may be too low. Check for correct drives.
  • Check to see if the dampers or registers are closed. If so, open them.
  • Inspect filters to see if they are dirty or clogged. Clean or replace them if neccessary.
  • Check for leaks in duct work. Repair if neccessary.
  • Check for elbows, cabinet walls, or other obstructions and correct if neccessary.
  • Check for belt slippage. Adjust or replace belts if neccessary.

Guides

Galt Display Rack

Cambridge, Ontario

Indoor air quality was a big problem for the Galt Display Rack Company. Employing welding applications in their manufacturing process, their workers were exposed to a number of toxic fumes on a routine basis. Learn how Diversitech was able to provide an effective solution.

Learn More

Related Products

In stock

Filterhawk FH-04 Cartridge Dust Collector

A four-cartridge solution featuring an innovative, modular design that effectively eliminates dust, smoke and other airborne contaminates from your work environment.

VIEW DETAILS
GET A QUOTE
In stock

Filterhawk FH-06 Cartridge Dust Collector

A six-cartridge solution featuring an innovative, modular design that effectively eliminates dust, smoke and other airborne contaminates from your work environment.

VIEW DETAILS
GET A QUOTE
In stock

Filterhawk Ambient Tower Collector

Designed to collect and sequester hazardous dust, smoke, fumes and other airborne particulates, the Airhawk Ambient Tower Collector pulls contaminated shop air through high-efficiency Nanofiber filters.

VIEW DETAILS
GET A QUOTE
In stock

AM-Series 4500 Ambient Air Cleaner

Diversitech’s Filterhawk AM-Series 4500 Ambient Air Cleaners are packaged air filtration systems that are designed to eliminate dust, smoke and other airborne pollutants with a high efficiency filtration system.

VIEW DETAILS
GET A QUOTE

About Us

Products

Industrial Solutions

Health & Safety

Services

Additional Resources

© 2025 Diversitech Equipment & Sales (1984) Ltd. All Rights Reserved.

Request A Quote

Please provide the information requested below so we can provide you with a timely and customized solution for your specific needs.